Remotely Monitor Tank Levels Part 1/2- Installing Tank Sensor

-
Utilizing the following components, IDX was quickly able to monitor the irrigation supply tank at our offices in Fourways. 

 To complete this task we would be using the Netbiter Remote tank monitoring solution with the following components.
  • eWON Netbiter - EC Range, Remote Monitoring GSM controller
  • eWON Netbiter - Ultrasonic Tank Sensor
The first step was installing the ultrasonic sensor on the storage tank

 Step 1 - Measure
The Netbiter Ultrasonic Tank Sensor comes with an included metal washer, this acts as a perfect stencil to outline the required holes. The center hole required is 30 mm, however we utilised a 32 mm drill mounted hole cutter. Ensure the sensor is mounted on the top surface of the tank, as horizontal as possible, with a clear view down to the contents of the tank and not a side wall or obstacle.


Step 2 - Drill
Using a 32 mm drill mounted hole cutter, this task was made effortless. However it is important to use a file or course sanding paper afterwards to clean off rough edges and loose bits, in order to ensure a water tight seal. We used a 4 mm drill bit for the screw holes. 




Step 3 - Mount

It is recommended that on uneven or non-rigid surfaces, the supplied rubber gasket and metal washer be utilised to create an IP65 seal between the sensor and the tank, especially in the cases of fuel tanks that could be contaminated by water.
We utilised large washers below the surface to ensure a rugged connection.





 Step 4 - Sensor Cover (Sun protection)

you should avoid leaving the sensor in direct sun light, we decided to re-purpose a plastic container to shade the sensor. This will prevent any inaccurate readings that may be caused by direct sunlight, in addition it will protect the sensor from the external elements, taken into consideration that the sensor has an IP65 rating and can be utilised in wet and harsh environments.


Step 5 - Wiring
The Netbiter Ultrasonic Sensor comes with 10 meter power and data supply cable. The M12 connector screws with a water tight connection onto the back of the sensor. We ran the cable into our office ceiling, and then into a distribution cabinet with our Netbiter EC250 and power supply.





The supplied cable has four cores, and should be wired as follows:

  • Black - RS-485 Line A
  • White - RS-485 Line B
  • Blue - 0 V DC
  • Brown - 24V DC 

If the tank sensor is your only device on the network, it is standard practice to terminate on both ends of the segment (at both the sensor and EC250 - GSM controller). The sensor has a built in terminating resistor that can be turned on and off via the RS485 bus, therefor placing a 120 Ohm resistor between line A and B on the Netbiter is required.




For more information on how you can monitor your tank levels and assets remotely contact the IDX team: info[at]idx.co.za


 The next step is configuration of the online server (Netbiter Argos), we will cover these steps in a following blog, to view:
click here

Popular posts from this blog

Common pitfalls when installing a Modbus RS485 network on site

-
Image
Last week IDX were called to site at  a large commercial residence building in Pretoria, South Africa. Where our  client was implementing an IoT solution for remote monitoring and control of various HVAC and power systems in the building.  The control system the SI chose in this case was a Modbus enabled Industrial Micro PC called the Revolution PI. The client had Modbus sensors connected to boilers, air conditioning systems, ventilation systems and power meters. The Modbus  communications between the controller and the sensors were intermittently failing due to various installation and implementation faults: 1. Earthing and Shielding Within any fieldbus communication installation, one of the requirements to ensure uninterrupted operation is to implement adequate grounding and shielding techniques. Effective grounding and Shielding help to prevent electrostatic and electromagnetic pickup, which can lead to failed communications. Some of the shielding and grounding req
Read more

IDX 8 Tag Manager - Managing the unmanagable?

-
Image
Tag management of real-time data systems can prove challenging. As an industrial IT company we frequently come across the problem where tags need to be migrated from one system to another or where tags need to be synchronised and maintained between systems including historians. Generally, this ends up being a manual process, often involving Excel and much diligence and patience of the maintainer’s behalf. IDX Unifig was the first incarnation of a tool we designed with the aim to simplify the migration and management of tags between systems. The tool worked, but with as with most first editions of software tools, we could see the need for improvement and refinement of the approach used. Thus Tag Manager was born, and has become the key stone in the IDX 8 software suite. All other IDX 8 modules, such as Data Exchange, Alarms and Events and the Historian use Tag Manager to store and reference tags. The comparison result we like to see - no changes.   Tag Manager employs a plug
Read more

How to connect to a Pepperl & Fuchs Advanced diagnostics module (ADM) using RS485 and Pactware

-
Image
Quick guide to get access to the P+F advanced diagnostic module via RS485 and COM converter. In order to do this, you need an RS485 converter which can convert RS485 to either ethernet or USB. I used a device from HMS (Anybus) called the Serial Server ( AB7701 ). This device connects to RS232, 422 or 485 and makes the data available over ethernet to your computer using a virtual com port. Connect the converter to the Diagnostic bus connection on the Pepperl & Fuchs fieldbus power hub 1. Once you have the com port available on your PC, Check the comport number via “manage my computer” Make sure that the FieldConnexd Diagnostic server (FDS) is running. Go to “Windows button”>“All programs” > “Pepperl+Fuchs” and start FDS control center In case the FDS is not running click onto “Start FDS” (in case it is running nothing is left to do here) click onto “Hide”. To avoid that this piece of software will be forgotten in future click onto settings and choose un
Read more